Ohms law calculator magic triangle ohm's law pie chart mathematical electric voltage electric current amperes watt's law emf power formulas resistance Ohm volts amperes calculate E V = I R emf P = V I specific electrical resistance conductivity resistivity relation relationship - sengpielaudio

= reset.

Formulas: V = I × R I = V / R R = V / I

The mathematical formulas of Ohm’s Law

Ohm’s Law can be rewritten in three ways for calculating current, resistance, and voltage.
If a current I should flow through a resistor R, the voltage V can be calculated.
First Version of the (voltage) formula: V = I × R

If there is a voltage V across a resistor R, a current I flows through it. I can be calculated.
Second Version of the (current) formula: I = V / R

If a current I flows through a resistor, and there is a voltage V across the resistor. R can be calculated.
Third Version of the (resistance) formula: R = V / I

All of these variations of the so called “Ohm’s Law” are mathematically equal to one another.

Name Formula sign Unit Symbol
voltage V or E volt V
current I ampere (amp) A
resistance R ohm Ω
power P watt W

What is the formula for electrical current?
When the current is constant:
I = Δ Q / Δ t
I is the current in amps (A)
Δ Q is the electric charge in coulombs (C),
that flows at time duration of Δ t in seconds (s).

Voltage V = current I × resistance R

Power P = voltage V × current I

In electrical conductors, in which the current and voltage are proportional
to each other, ohm’s law apply: V ~ I or VI = const.

Constantan wires or other metal wires held at a constant temperature meet well ohm’s law.

VI = R = const.” ist not the law of ohm. It is the definition of the resistance.
Thereafter, in every point, even with a bent curve, the resistance value can be calculated.

For many electrical components such as diodes ohm’s law does not apply.

“Ohm’s Law” has not been invented by Mr. Ohm

UI = R = const.” is not the law of Ohm or Ohm’s law. It is the definition of the resistance.
Thereafter, in every point – even with a bent curve – the resistance value can be calculated.
Ohm’s law “postulates” following relationship: When a voltage is applied to an object, the electric
current flowing through it changes the strength proportional to the voltage. In other words, the
electrical resistance, defined as the quotient of voltage and currentis constant, and that is
independent of voltage and current. The name of the law “honors” Georg Simon Ohm, who could
prove this relationship for some simple electrical conductors as one of the first searchers.
“Ohm’s Law” has really not been invented by Ohm.

The magic triangle Tip: Ohm’s magic triangle

The magic V I R triangle can be used to calculate all formulations of ohm’s law.
Use a finger to hide the value to be calculated. The other two values then show
how to do the calculation.

The symbol I or J = Latin: influare, international ampere, and R = resistance. V = voltage or
electric potential difference, also called voltage drop, or E = electromotive force (emf = voltage).

Voltage drop calculations – DC / single phase calculation
The voltage drop V in volts (V) is equal to the wire current I in amps (A) times twice
the wire length L in feet (ft) times the wire resistance per 1000 feet R in ohms (Ω / kft)
divided by 1000:
Vdrop (V) = Iwire (A) × Rwire (Ω)
= Iwire (A) × (2 × L (ft) × Rwire (Ω / kft) / 1000 (ft / kft))

The voltage drop V in volts (V) is equal to the wire current I in amps (A) times twice
the wire length L in meters (m) times the wire resistance per 1000 meters R in ohms
(Ω / km) divided by 1000:
Vdrop (V) = Iwire (A) × Rwire (Ω)
= Iwire (A) × (2 × L (m) × Rwire (Ω / km) / 1000 (m / km))

If the unit of power P = I × V and of voltage V = I · R is needed,
look for Red Power Dot “The Big Power Formulas”:
Calculations: power (watt), voltage, current, resistance

Some persons think that Georg Simon Ohm calculated the “specific resistance”.
Therefore they think that only the following can be the true ohm’s law.

Quantity of resistance
Formel
R = resistance Ω
ρ = specific resistance Ω×m
l = double length of the cable m
A = cross section mm2

Electrical conductivity (conductance) σ (sigma) = 1/ρ
Specific electrical resistance (resistivity) ρ (rho) = 1/σ

Difference between electrical resistivity and electrical conductivity

The conductance in siemens is the reciprocal of the resistance in ohms.

Simply enter the value to the left or the right side.
The calculator works in both directions of thesign.
The value of the electrical conductivity (conductance) and the specific electrical resistance
(resistivity) is a temperature dependent material constant. Mostly it is given at 20 or 25°C.
Resistance R = ρ × (l / A) or R = l / (σ × A)

For all conductors the specific resistivity changes with the temperature. In a limited
temperature range it is approximately linear:
Temperature dependence where α is the temperature coefficient, T is the temperature and T0 is any temperature,
such as T0 = 293.15 K = 20°C at which the electrical resistivity ρ (T0) is known.

Cross-sectional area – cross section – slice plane

Now there is the question:
How can we calculate the cross sectional area (slice plane) A
from the wire diameter d and vice versa?

Calculation of the cross section A (slice plane) from diameter d:
Formula calculation diameter
r = radius of the wire
d = diameter of the wire

Calculation diameter d from cross section A (slice plane):
Formel Berechnung Durchmesser aus Querschnitt
Cross section A of the wire in mm2 inserted in this formula gives the diameter d in mm.

Calculation − Round cables and wires:
• Diameter to cross section and vice versa •

Electric voltage V = I × R (Ohm’s law VIR)
Electrical voltage = amperage × resistance (Ohm’s law)
Please enter two values, the third value will be calculated.
Electric power P = I × V (Power law PIV)
Electric power = amperage × voltage (Watt’s Law)
Please enter two values, the third value will be calculated.

Ohm’s law. V = I × R, where V is the potential across a circuit element, I is the current
through it, and R is its resistance. This is not a generally applicable definition of
resistance. It is only applicable to ohmic resistors, those whose resistance R is
constant over the range of interest and V obeys a strictly linear relation to I. Materials
are said to be ohmic when V depends linearly on R. Metals are ohmic so long as one
holds their temperature constant. But changing the temperature of a metal changes R
slightly. When the current changes rapidly, as when turning on a light, or when using AC
sources, slightly non-linear and non-ohmic behavior can be observed. For non-ohmic
resistors, R is current-dependent and the definition R = dV/dI is far more useful. This is
sometimes called the dynamic resistance. Solid state devices such as thermistors are
non-ohmic and non-linear. A thermistor’s resistance decreases as it warms up, so its
dynamic resistance is negative. Tunnel diodes and some electrochemical processes
have a complicated I to V curve with a negative resistance region of operation. The
dependence of resistance on current is partly due to the change in the device’s
temperature with increasing current, but other subtle processes also contribute to
change in resistance in solid state devices.

Calculation: Parallel Resistance (Resistor) Calculator

Color Code Calculator for Resistors

Electric Current, Electric Power, Electricity and Electric Charge

The Formula Wheel – Formulas of Electrical Engineering

In acoustics we use “Ohm’s law as acoustic equivalent

How electricity works.
Ohm’s Law clearly explained.
Electricity explained

[top of page]

Source

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Comment moderation is enabled. Your comment may take some time to appear.